skip to main content
Ngôn ngữ:
Giới hạn tìm kiếm: Giới hạn tìm kiếm: Dạng tài nguyên Hiển thị kết quả với: Hiển thị kết quả với: Chỉ mục

Si poisoning and promotion on the microstructure and mechanical properties of Al–Si–Mg cast alloys

Dong, Xixi ; Ji, Shouxun

Journal of Materials Science, 2018, Vol.53(10), pp.7778-7792 [Tạp chí có phản biện]

ISSN: 0022-2461 ; E-ISSN: 1573-4803 ; DOI: 10.1007/s10853-018-2022-0

Toàn văn sẵn có

Trích dẫn Trích dẫn bởi
  • Nhan đề:
    Si poisoning and promotion on the microstructure and mechanical properties of Al–Si–Mg cast alloys
  • Tác giả: Dong, Xixi ; Ji, Shouxun
  • Chủ đề: Alloys – Mechanical Properties ; Porosity – Mechanical Properties ; Metals (Materials) – Mechanical Properties ; Specialty Metals Industry – Mechanical Properties ; Poisoning – Mechanical Properties
  • Là 1 phần của: Journal of Materials Science, 2018, Vol.53(10), pp.7778-7792
  • Mô tả: Hypoeutectic Al– x Si–0.45Mg ( x  = 6.5, 7.5, 8.5, 9.5) alloys were refined by Al5Ti1B containing TiB 2 and Al3Ti3B containing TiB 2 and AlB 2 , respectively. With increasing Si, Si poisoning on TiB 2 results in the obvious coarsening of primary α -Al in Al5Ti1B-refined alloys from 350 ± 40 to 400 ± 50, 475 ± 50 and 560 ± 80 μm, and the competition between Si promotion on AlB 2 and Si poisoning on TiB 2 leads to the slight coarsening of primary α -Al in Al3Ti3B-refined alloys from 215 ± 30 to 265 ± 35, 265 ± 30 and 315 ± 25 μm. After T6 heat treatment, with increasing Si, the yield strength (YS) of Al5Ti1B-refined alloys increases from 294 ± 2 to 299 ± 2, 304 ± 1 and 309 ± 2 MPa, and the elongation first increases from 3.5 ± 0.8 to 4.5 ± 1.0 and 7.8 ± 1.4%, after decreases to 5.5 ± 1.2%, while the YS of the Al3Ti3B-refined alloys increases from 300 ± 1 to 305 ± 2, 312 ± 1 and 317 ± 2 MPa, and the elongation increases from 6.1 ± 1.1 to 8.5 ± 1.2, 11.8 ± 1.5 and 12.1 ± 1.6%. The increase in the secondary phase and precipitation strengthening results in the increase in strength with increasing Si. With increasing Si, the decrease in porosity formation by decreasing solidification interval and increasing fluidity is superior to the increase in porosity formation by slightly coarsening grain size, which leads to the increase in ductility in the Al3Ti3B-refined alloys, while the competition between porosity decreasing and increasing factors leads to the inverted ‘V’-shaped evolution of ductility in the Al5Ti1B-refined alloys.
  • Ngôn ngữ: English
  • Số nhận dạng: ISSN: 0022-2461 ; E-ISSN: 1573-4803 ; DOI: 10.1007/s10853-018-2022-0

Đang tìm Cơ sở dữ liệu bên ngoài...