skip to main content
Ngôn ngữ:
Giới hạn tìm kiếm: Giới hạn tìm kiếm: Dạng tài nguyên Hiển thị kết quả với: Hiển thị kết quả với: Chỉ mục

Heat transfer and cracking performance of endothermic hydrocarbon fuel when it cools a high temperature channel

Yue, Lei ; Wu, Jianzhou ; Gong, Yu ; Hou, Jingwei ; Xiong, Liangping ; Xiao, Chengjian ; Fang, Wenjun

Fuel Processing Technology, August 2016, Vol.149, pp.112-120 [Tạp chí có phản biện]

ISSN: 0378-3820 ; E-ISSN: 1873-7188 ; DOI: 10.1016/j.fuproc.2016.04.017

Toàn văn sẵn có

Phiên bản sẵn có
Trích dẫn Trích dẫn bởi
  • Nhan đề:
    Heat transfer and cracking performance of endothermic hydrocarbon fuel when it cools a high temperature channel
  • Tác giả: Yue, Lei ; Wu, Jianzhou ; Gong, Yu ; Hou, Jingwei ; Xiong, Liangping ; Xiao, Chengjian ; Fang, Wenjun
  • Chủ đề: Heat Transfer ; Cracking ; Hydrocarbon Fuel ; Heat Sink ; Safe Run Time (Srt) ; Engineering
  • Là 1 phần của: Fuel Processing Technology, August 2016, Vol.149, pp.112-120
  • Mô tả: To link to full-text access for this article, visit this link: http://dx.doi.org/10.1016/j.fuproc.2016.04.017 Byline: Lei Yue, Jianzhou Wu, Yu Gong, Jingwei Hou, Liangping Xiong, Chengjian Xiao, Wenjun Fang Abstract: Jet fuel is used as a coolant before it is burned in the combustor of the aircraft. Insoluble particles and surface deposits can impair engine performance. Jet fuel thermal oxidation test (JFTOT) defines the standard test method for evaluation of the deposit formed through heating fuels in tubes caused by thermal oxidation (<400[degrees]C). At a higher temperature, fuel in the heating process decomposes leading to surface deposits by coking. In this work, we propose a method to evaluate the security of fuel flowing in the tube at high temperatures (>500[degrees]C). The heat transfer and cracking performances of two hydrocarbon fuels which are laboratory modified aviation kerosene (Fuel 1 ([rho] =0.85g/cm.sup.3) and Fuel 2 ([rho] =0.78g/cm.sup.3)) have been investigated in a heat-exchanger under supercritical conditions (T =700-770[degrees]C, p =2.5-5.5MPa, m =0.4-1.0g/s). The temperature and flow rate in this work are much higher than those in JFTOT. The safe run time (SRT) is used to evaluate the heat transfer security of each fuel. As the temperature increases or the flow rate decreases or the pressure increases, the SRTs of Fuel 1 and Fuel 2 decrease clearly. In general, the heat transfer security of Fuel 1 is better than that of Fuel 2. Moreover, the volumetric heat sink of Fuel 1 is larger than that of Fuel 2. So, the overall performance of Fuel 1 is more excellent when it is used as propellant and coolant for hypersonic aircraft. In consideration of the heat transfer security, heat sink and the required driving force for aircraft, the temperature of fuel at the exit of heat transfer passage should be set as 740[degrees]C, the flow rate of fuel should be 0.6-1.0g/s, the pressure of heat transfer passage should be 3.5MPa. Based on these results, we find that the modification of a high density fuel is an effective way to prepare an advanced hydrocarbon fuel. Article History: Received 5 December 2015; Revised 30 March 2016; Accepted 14 April 2016
  • Ngôn ngữ: English
  • Số nhận dạng: ISSN: 0378-3820 ; E-ISSN: 1873-7188 ; DOI: 10.1016/j.fuproc.2016.04.017

Đang tìm Cơ sở dữ liệu bên ngoài...